Skip to product information
Sale
  • Sku: XPW10918546

XPARTCO W10918546 Gas Range Oven Igniter

List Price:  $36.00
$27.90
 per 

FREE SHIPPING TO ALL 48 CONTIGUOUS STATES
Free standard shipping at checkout.

CHECK YOUR MODEL COMPATIBILITY

Enter your appliance model number to check if this part is listed as compatible.

Need help finding your model number?

Guaranteed safe checkout

Product description

XPARTCO W10918546 Gas Range Oven Igniter — XPARTCO Aftermarket

Product Description

The XP-W10918546 is an XPARTCO aftermarket replacement oven igniter for Whirlpool-manufactured gas ranges. When a gas oven stops heating, the igniter is the most likely failed component — but a systematic diagnostic approach helps confirm the failure before ordering. Start by testing the stovetop burners. If the surface burners light normally, the gas supply to the range is working and the problem is isolated to the oven circuit. If the stovetop burners also fail to light, the issue is upstream — a closed gas valve, a supply line problem, or a utility interruption — and the igniter is not the cause.

With gas supply confirmed, turn the oven on and observe the igniter through the vent or the opening in the oven floor. In a working oven, the flat igniter element should begin to glow within seconds. If the igniter does not glow at all, either the element itself has failed (open circuit) or the electrical path to the igniter is broken — a blown thermal fuse, a failed oven control board, or a wiring issue. If the igniter glows but the gas does not light, the igniter is drawing below the current threshold the gas valve requires to open. This is the classic failure pattern: the igniter has degraded enough that it cannot pull sufficient current through the safety valve circuit, even though it still produces visible heat. The gas valve itself is rarely the failed component — in the vast majority of "glows but won't light" cases, replacing the igniter restores normal operation.

A third scenario is intermittent ignition — the oven sometimes lights and sometimes does not, or the preheat time has gradually increased from its original duration. This indicates an igniter that is degrading but has not yet fully failed. It is drawing current near the valve's threshold and sometimes crosses it, sometimes does not. Replacing the igniter now avoids a complete no-heat failure later.

Quick Answer

How to Diagnose an Oven Igniter Failure

Test the stovetop burners first — if they work, gas supply is confirmed. Turn the oven on and watch the igniter through the oven floor. No glow = element or wiring failure. Glows but gas won't light = igniter too weak to open the gas valve (most common failure). Slow preheat = igniter degrading. In all three cases, replace the igniter before suspecting the gas valve. The igniter fails far more often than the valve.

Common Symptoms

  • Oven igniter glows but gas burner does not light
  • Oven preheat time has gradually increased over weeks or months
  • Igniter does not glow at all — no visible heat from the element
  • Oven ignites intermittently — works sometimes, fails other times
  • Gas odor when oven is turned on without ignition (turn off immediately)

Replaces Part Numbers

The XP-W10918546 replaces the Whirlpool OEM oven igniter W10918546 and all associated cross-reference numbers for this flat-style bake igniter.

XP-W10918546 replaces W10918546, WP3186491, W10140611, 3186491, 98005652, WPW10140611, 4454963, W10918546VP, OEM18111615, AP6037202, AWP42687, PD00031392, PS11770066

Compatibility & Model Cross Reference

This aftermarket oven igniter fits select gas ranges manufactured by Whirlpool Corporation across multiple brand names. Always verify your specific model number before ordering.

Whirlpool: SF265LXTS2, SF315PEPQ2, WFG320M0BS0, SF362LXSY0, SF368LEPQ1, WFG515S0ES0

Maytag: MGR5605WB0, MGR5605WW0, AGR4422VDD0, AGR4422VDS0

Amana: AGG222VDB0, AGG222VDW1, AGR3311WDW0, AGR4230BAB0

Roper: FGP305KN0, FGP305KW7, FGP325GN0, FGP325LQ1

Estate: TGP305TQ2, TGP305TT2, TGP325LQ1, TGP325LW0

Magic Chef: CGR3765ADC, CGR3765ADW, CGR3765BDC

Ikea: Select Ikea-branded gas range models manufactured by Whirlpool

Kenmore: 66575775890, 66575776890, 66575779890

This is a partial list of verified sample models — not every model from these brands uses this igniter. Your model number is typically on a label inside the oven door frame or on the back of the range. Not sure if this fits? Send us your model number and we'll confirm compatibility before you order.

Key Features

  • XPARTCO aftermarket oven igniter — replacement for Whirlpool OEM W10918546
  • Flat-style igniter with ceramic housing and wire connector
  • Fits select Whirlpool, Maytag, Amana, Roper, Estate, Magic Chef, Ikea, and Kenmore gas ranges
  • Igniter element with two-wire harness and male pin connector
  • Direct replacement — mounts in the original igniter bracket position

Product Specifications

Part Number XPW10918546
Condition Aftermarket
Brand XPARTCO
OEM Part Number W10918546
Part Type Gas Oven Igniter
Igniter Style Flat (Norton-type)
Appliance Type Gas Range / Oven
Connector Type Two-wire harness with male pin connector

Installation & Safety Notes

Gas Appliance — Read Before Installing
Turn off the gas supply to the range and unplug the range from electrical power before beginning work. The igniter element is extremely fragile — handle it only by the ceramic mounting block or wiring, never the flat element surface. Wear clean gloves; skin oils contaminate the element and cause premature failure. Remove the oven racks and oven floor panel to expose the igniter. Disconnect the wire connector, remove the mounting screws, and carefully lift out the old igniter. Position the new igniter in the same orientation, secure the mounting screws, and reconnect the wire connector. Replace the oven floor panel and racks. Restore gas supply and power. Turn the oven on to verify the igniter glows and the gas lights normally. If you smell gas at any point during or after installation, shut off the gas supply immediately and ventilate the area.

Frequently Asked Questions

My stovetop burners work but the oven won't heat — is it the igniter?
Most likely yes. Working stovetop burners confirm gas is reaching the range. The oven has its own igniter and gas valve circuit, independent of the stovetop. Turn the oven on and look at the igniter through the oven floor opening. If it glows but the gas does not light, the igniter has weakened to the point where it cannot draw enough current to open the gas valve. This is the most common oven igniter failure and means the igniter — not the gas valve — needs replacement.
Can a weak igniter cause uneven baking or temperature swings?
Yes. A degrading igniter takes longer to reach the current threshold that opens the gas valve. Each time the oven cycles (the thermostat calls for heat and the igniter must relight the burner), a weak igniter creates a longer delay between the heat call and actual ignition. This results in wider temperature swings inside the oven — the cavity cools more between cycles than it should. If your baking results have become inconsistent even though you have not changed settings, a weak igniter is a likely cause.
Could the problem be the oven control board instead of the igniter?
It is possible but far less common. If the igniter does not glow at all, the control board could be failing to send power to the igniter circuit. However, a no-glow condition more often points to a failed igniter element (open circuit), a blown thermal fuse, or a loose wire connection. Check the simplest and most common failures first: the igniter itself, then the thermal fuse if your range has one, then wiring connections. The control board is typically a last resort after the more common causes are ruled out.
How long should the igniter take to light the oven?
A new igniter in good condition typically lights the oven burner within 30 to 90 seconds of turning the oven on. The igniter must heat up enough to draw sufficient current through the gas valve circuit before the valve opens. If your oven takes significantly longer than this — several minutes or more — the igniter is degrading. Exact times vary by model and gas pressure, but a consistent increase from the oven's original behavior is the meaningful indicator.
What is the difference between a flat igniter and a round igniter?
Gas oven igniters come in two main styles: flat (also called Norton-type or silicon carbide) and round (also called carborundum or mini-round). The XP-W10918546 is a flat-style igniter. Flat and round igniters are not interchangeable — they have different mounting configurations, different electrical characteristics, and different connector types. Your range is designed for one specific style. Check your model's parts diagram to confirm which type your oven requires before ordering. Using the wrong style will not fit the mounting bracket and will not function correctly.
XPARTCO Aftermarket Part Fast Shipping Easy Installation
View full details
XPARTCO W10918546 Gas Range Oven Igniter

XPARTCO W10918546 Gas Range Oven Igniter

List Price:  $36.00
$27.90
 per 
SUBHEADING

Recently viewed products

Free Shipping

Fast, Free Shipping – No Surprises, Just Savings! Enjoy FREE shipping on all orders within the continental United States. No minimums, no hidden fees—just the parts you need, delivered straight to your door at no extra cost!

Top-notch support

Because Your Time Matters! At Express Parts Direct, we’re committed to providing exceptional customer service. Whether you need help finding the right part, troubleshooting an issue, or tracking your order, our knowledgeable team is here to assist you every step of the way. Experience fast, friendly, and expert support—because you deserve the best!

Satisfied or refunded

100% Satisfaction or Your Money Back! We stand by the quality of our parts and service. If you’re not completely satisfied, we’ll make it right—or refund your purchase. Shop with confidence knowing that your satisfaction is our priority!