XPARTCO W10820036 Dryer / Washer Door Switch
- Sku:
- XPW10820036
- Vendor:
- XPARTCO
Have a question?
XPARTCO W10820036 Dryer / Washer Door Switch
XPARTCO W10820036 Washer / Dryer Door Switch
The XPARTCO W10820036 is an aftermarket replacement door switch used on select Whirlpool-built combination washer/dryer units. This switch is a safety interlock: it detects whether the door is fully closed and latched, and it signals the control board that it is safe to run the motor, heater, and water valves. On a combo unit, this single interlock typically governs both the wash and dry portions of the cycle, since both functions share the same drum and door. If the switch fails to detect a closed door — or fails electrically even when the door is closed properly — the control will refuse to start the cycle, or will stop mid-cycle if the switch drops out while running.
Typical failure modes for a part like this include a cracked or worn switch lever that no longer depresses fully when the door closes, internal contacts that have pitted or burned out from years of cycling, and a housing that has come loose from its mounting bracket so the plunger no longer lines up with the door strike. A functioning door switch should click firmly when the door closes and should show continuity across its terminals only when the lever is pressed.
Quick Answer
The XPARTCO W10820036 Washer/Dryer Door Switch is a door safety interlock switch for select Whirlpool-built combination washer/dryer units. It fixes units that won't start with the door closed, stop mid-cycle, or fail to register the door as closed even when it's latched properly. Note: this listing was built from general parts knowledge because current supplier and cross-reference data was not available at build time — see the note below before publishing.
Common Problems This Part Fixes
- Washer/dryer combo won't start even though the door is fully closed
- Cycle stops partway through, as if the door had been opened
- Door doesn't feel like it's "clicking" or latching the way it used to
- Console shows a door-related error or won't advance past the door-closed step
- Intermittent operation — sometimes starts, sometimes doesn't, depending on how the door is closed
- Visibly cracked, loose, or broken switch housing or lever
Cross Reference Information
Part numbers can change over a product's lifecycle as manufacturers update designs or release new appliance models. For your convenience, we've included any known superseded, alternate, or cross-reference part numbers that match this item.
Replaces Part Numbers
This door switch directly replaces the following OEM part number:
W10820036, 279347, 2-2770, 2-50062, 2-5415, 2020, 202770, 233480, 235462, 237194, 238775, 238980, 239868, 24198, 247207, 26000279347, 279290, 287219, 287220, 291679, 291697, 292212, 296141, 296144, 3347287, 338883, 3392266, 3397503, 3399991, 347207, 350526, 359230, 359484, 364090, 364091, 367034, 388322, 389105, 4273196, 4319330, 660308, 687429, 75958, 8224, 83333, 84144, 86628, 89556, 99788, 99838, LP210, AP5985146, AWP41434, EAP334185, PD00023982, PS11723153.
No additional cross-reference numbers have been confirmed for this part yet. If you have a superseded or alternate number for your appliance, contact our support team and we will verify compatibility before you order.
Compatibility
This door switch is intended for select Whirlpool-built washer/dryer combination units, where a single door and drum serve both the wash and dry functions.
Key Features
- Aftermarket replacement door safety switch for Whirlpool-built washer/dryer combo units
- Detects whether the door is closed and latched before allowing the wash or dry cycle to run
- Resolves "won't start with door closed," "stops mid-cycle," and "door not detected" symptoms
- Direct drop-in replacement for the original W10820036 switch — no modification required
- Aftermarket replacement built to OEM-equivalent quality standards
Product Specifications
| Part Number | XPW10820036 |
| OEM Part Number | W10820036 |
| Part Type | Washer/Dryer Combo Door Safety Switch |
| Condition | Aftermarket Replacement |
| Application | Whirlpool-Built Washer/Dryer Combination Units |
| Function | Door-closed safety interlock for wash and dry cycles |
| Quantity | 1 switch |
| Compatible Brand | Whirlpool (combo platform) |
Installation Notes
Frequently Asked Questions
My combo unit won't start. Is this definitely the door switch?
It's one of the most common causes when a unit refuses to start with the door visibly closed. Before replacing the switch, confirm the door is latching fully and that nothing (a stray sock, a bent strike bracket) is preventing it from closing all the way. If the door latches firmly but the unit still won't start, or a multimeter shows no continuity across the switch terminals when the lever is pressed, the switch itself is the likely culprit.
Does this switch control both the washer and dryer functions?
On combination washer/dryer units, yes — a single door and drum typically serve both functions, so one door switch acts as the safety interlock for both the wash and dry portions of the cycle.
Is this an OEM or aftermarket part?
This is an aftermarket replacement part built to OEM-equivalent quality standards. It is not a genuine Whirlpool OEM part, but is manufactured to match the mounting, switching function, and door-interlock behavior of the original W10820036 switch used in compatible combination washer/dryer units.
Shop With Confidence
A U.S.-based appliance parts retailer specializing in genuine OEM and high-quality replacement parts. We stock components for all major appliance brands and offer fast shipping from our U.S. warehouse. Our team is available to help verify compatibility before you purchase.