Skip to product information
Sale
  • Sku: WH16X27182

WH16X27182 Washer Genuine Suspension Rod Assembly

List Price:  $38.00
$28.80
 per 

FREE SHIPPING TO ALL 48 CONTIGUOUS STATES
Free standard shipping at checkout.

CHECK YOUR MODEL COMPATIBILITY

Enter your appliance model number to check if this part is listed as compatible.

Need help finding your model number?

Guaranteed safe checkout

Product description

WH16X27182 Washer Suspension Rod Assembly (24-Inch) — Genuine OEM

Product Description

The WH16X27182 is a genuine OEM 24-inch suspension rod assembly for GE unitized laundry centers. It supports the washer tub inside the cabinet and dampens tub movement during the wash and spin cycles. When these rods wear out, the most noticeable symptom is excessive vibration — but vibration in a laundry center has several possible causes, and replacing suspension rods when the actual problem is an unlevel machine or a weak floor wastes time and money. This listing walks through the diagnostic steps to confirm whether worn suspension rods are actually your problem before you order.

A GE unitized laundry center is a tall, heavy stacked appliance with the washer on the bottom and the dryer on top. That high center of gravity makes it more sensitive to vibration than a standalone washer. The suspension rods connect the inner washer tub to the outer cabinet and absorb the forces generated when wet laundry shifts during agitation and spin. When the rods lose their damping ability, those forces transfer directly into the cabinet and through the floor. But the same symptom — a machine that shakes, walks, or bangs — can also come from an unlevel unit, a floor that flexes under load, chronically unbalanced loads, worn tub bearings, or even shipping bolts that were never removed after delivery.

Quick Answer

How to Diagnose Suspension Rod Failure vs. Other Vibration Causes

Before ordering suspension rods, rule out the simpler causes first. Confirm the laundry center is level using a bubble level on top of the washer tub — adjust the front leveling legs until the bubble is centered. Check that the unit sits on a solid surface; a laundry center on a wood-frame floor may vibrate because the floor itself flexes, not because the rods are worn. Run a small, balanced test load — if severe vibration happens even with a few towels distributed evenly, the problem is mechanical, not load distribution. Then open the washer lid and push down firmly on the tub with both hands. Release and watch: a healthy suspension lets the tub drop and return to center in one or two controlled bounces. If the tub bounces repeatedly, swings side to side, or drops and stays low, the suspension rods have lost their damping and need replacement.

Common Symptoms

  • Excessive vibration and shaking during wash or spin cycle
  • Loud banging or thumping sounds from inside the cabinet
  • Laundry center walks or shifts across the floor during operation
  • Washer tub visibly off-center or tilted when at rest
  • Vibration that worsens over time or with loads the machine previously handled

Replaces Part Numbers

The WH16X27182 is the current GE part number for this 24-inch washer suspension rod assembly. It replaces the following part and catalog numbers.

WH16X27182 replaces 4588128, AGE26970, AP6328301, EAP12343389, PD00062746, PS12343389

Compatibility & Model Cross Reference

This genuine OEM suspension rod fits select GE-manufactured unitized laundry centers (stacked washer/dryer combos). Always confirm your specific model number against the manufacturer's parts diagram before ordering.

GE (General Electric): GUD24ESSM0WW, GUD24ESSM1WW, GUD24GSSM0WW, GUD24GSSM1WW

Hotpoint / RCA / Kenmore: Select unitized laundry center models using the same 24-inch rod platform

This is a partial list of verified sample models — not every model from these brands uses this rod. GE laundry centers use different rod lengths for different platforms — verify that your model requires the 24-inch rod. Your model number is typically on a label inside the washer lid or on the rear cabinet panel. Not sure if this fits? Send us your model number and we'll confirm compatibility before you order.

Key Features

  • Genuine OEM GE suspension rod assembly — 24 inches long
  • Steel shaft with spring damper and ball joints at each end
  • Designed for GE unitized laundry centers (stacked washer/dryer combos)
  • Sold individually — multiple rods per machine (check parts diagram for quantity)
  • Direct replacement for earlier revision WH16X27181
  • No electrical connections — purely mechanical installation

Product Specifications

Part Number WH16X27182
Condition New
Brand GE (General Electric)
Part Type Washer Suspension Rod Assembly
Appliance Type Unitized Laundry Center (Stacked Washer/Dryer)
Rod Length 24 inches
Material Steel shaft with spring and polymer ball joints
Quantity 1 (sold individually)
Supersedes WH16X27181

Installation & Safety Notes

Safety Warning
Unplug the laundry center from the wall outlet before beginning any work. This is a stacked unit — ensure it is stable and will not tip during service. Never attempt to tilt or move the unit alone. Wear work gloves to protect your hands from sharp cabinet edges. When removing the old rods, support the washer tub to prevent it from dropping onto internal components. After installing the new rod(s), confirm all mounting points are fully seated before restoring power.

Frequently Asked Questions

How do I rule out an unlevel machine before blaming the suspension rods?
Place a bubble level on top of the washer tub — not on the dryer top or the cabinet exterior, since those surfaces may not reflect the tub's actual orientation. If the bubble is off-center, adjust the front leveling legs until the unit is level both side to side and front to back. Many GE laundry centers have fixed rear legs and adjustable front legs. After leveling, run a test load. If the vibration stops, the rods were not the problem.
My laundry center sits on a wood-frame floor — could the floor be the issue?
Yes. A unitized laundry center weighs several hundred pounds, and during the spin cycle the unbalanced load generates lateral forces that can cause a wood-frame floor to flex. That floor deflection amplifies the vibration and can make it feel like the machine is shaking when the suspension system is actually fine. If possible, position the unit in a corner of the room where the floor joists are supported at both ends, or place a 3/4-inch plywood panel under the unit to distribute the load. If vibration is only noticeable on the upper floors of a house, the floor structure is likely contributing.
What does the tub bounce test tell me about the rods?
Open the washer lid, press firmly down on the tub with both hands, and release. With healthy suspension rods, the tub will drop slightly and return to center with one or two controlled bounces — the springs absorb and dissipate the energy quickly. If the tub bounces three or more times before settling, or if it swings side to side before coming to rest, the rod springs have lost their tension. If the tub drops and stays low without rebounding, a rod may be detached or its ball joint may have broken. This test checks the entire suspension system at once — it cannot tell you which individual rod has failed.
How can I tell which rod has failed if the bounce test shows a problem?
After confirming the suspension system is worn via the bounce test, you need to access the rods visually. With the laundry center unplugged, remove the cabinet access panel to expose the rod mounting points. Inspect each rod individually — look for a cracked or broken ball joint, a rod that has slipped out of its socket, visible corrosion on the spring, or a spring that appears stretched or compressed at rest compared to the other rods. Grasp each rod and push it up and down by hand — a healthy rod offers firm, even resistance. A worn rod compresses too easily or feels loose and rattles in its socket.
Can I replace just the one bad rod, or do I need to replace all of them?
Most technicians recommend replacing all rods at once. The suspension rods work as a balanced system — they share the load of dampening tub movement across multiple mounting points. A new rod with full spring tension paired with worn rods that have reduced tension creates uneven damping, which can make the tub track off-center and introduce a new wobble. If budget is a constraint, replacing just the failed rod will stop the immediate banging or detachment, but expect to replace the remaining rods within the next few months as they continue to degrade.
What other components should I inspect while the cabinet is open for rod replacement?
While you have access to the inside of the cabinet, inspect the rod mounting brackets on the cabinet frame — make sure they are not cracked, bent, or corroded. Check the tub bearing by grabbing the inner tub and trying to rock it — any play or grinding indicates bearing wear. Look at the drive belt (if applicable) for cracks or glazing, and inspect the motor coupler for wear. These components are easier to reach with the rods disconnected, and addressing them now saves the labor of opening the cabinet again later.
Genuine OEM Part Fast Shipping Easy Installation
View full details
WH16X27182 Washer Genuine Suspension Rod Assembly  Parts-O-Matic

WH16X27182 Washer Genuine Suspension Rod Assembly

List Price:  $38.00
$28.80
 per 

Model Compatibility

Search your appliance model number below. Supports partial or full model search.

🔍 Search Model Number

Type your full or partial model number above to instantly check if this part fits your appliance.

✓ Guaranteed Fit — exact model match found.
No matching model found. Please verify your full model number or contact support.
Loading compatible models...
Model Number Manufacturer Appliance Type

⚠️ This is a partial compatibility list. Always verify your appliance model number before ordering. Contact our support team if you’re unsure.

SUBHEADING

Recently viewed products

Free Shipping

Fast, Free Shipping – No Surprises, Just Savings! Enjoy FREE shipping on all orders within the continental United States. No minimums, no hidden fees—just the parts you need, delivered straight to your door at no extra cost!

Top-notch support

Because Your Time Matters! At Express Parts Direct, we’re committed to providing exceptional customer service. Whether you need help finding the right part, troubleshooting an issue, or tracking your order, our knowledgeable team is here to assist you every step of the way. Experience fast, friendly, and expert support—because you deserve the best!

Satisfied or refunded

100% Satisfaction or Your Money Back! We stand by the quality of our parts and service. If you’re not completely satisfied, we’ll make it right—or refund your purchase. Shop with confidence knowing that your satisfaction is our priority!