- Sku: WD08X23476
WD08X23476 Dishwasher Genuine OEM Tub Gasket
FREE SHIPPING TO ALL 48 CONTIGUOUS STATES
Free standard shipping at checkout.
CHECK YOUR MODEL COMPATIBILITY
Enter your appliance model number to check if this part is listed as compatible.
Need help finding your model number?
Water on the kitchen floor in front of a GE dishwasher usually points to the tub gasket. The WD08X23476 is the door-perimeter seal that sits in a channel around the tub opening and compresses against the door panel when the latch closes. When this gasket cracks, hardens, or loses its seat in the channel, water escapes past it during the wash and rinse phases and drips down the front of the tub. The leak is typically slow — a small puddle after a full cycle rather than a flood — and it may come and go depending on which cycle phase directs water toward the door.
Before replacing the gasket, it is worth confirming the gasket is actually the leak source. A dishwasher can leak from several other points — the door latch that is not pulling the door tight enough, a cracked spray arm throwing water at the wrong angle, the pump seal underneath, or the water inlet valve connection at the bottom. The gasket leak has a specific signature: water appears at the front edge of the tub, runs down the inside of the door or the face of the tub below the door opening, and collects under the front of the unit. If the water is coming from underneath the dishwasher or from the back, the gasket is not the problem.
If your GE or Hotpoint dishwasher leaks from the front door area during the wash cycle — and you can see water running down the inside of the door or the tub face below the door opening — the tub gasket is the most likely cause. The WD08X23476 is the genuine OEM replacement. If water is pooling under the center or rear of the dishwasher instead, check the pump seal, inlet valve, or hose connections first.
- Water pooling on the floor in front of the dishwasher after a cycle
- Water visible running down the inside of the door during operation
- Leak that appears only during certain wash or rinse phases
- Gasket is visibly cracked, stiff, or pulled out of its channel
- Moisture or water stains on the cabinet floor beneath the dishwasher door
The WD08X23476 is GE's current part number for this dishwasher tub gasket. It supersedes the earlier WD08X10088, WD08X20674, and WD08X22094 and is cross-referenced under the following distributor catalog numbers.
COMPATIBILITY
This genuine OEM tub gasket fits select GE, Hotpoint, and Crosley dishwashers with plastic tubs. Confirm your model number before ordering — GE uses a different gasket (WD08X23477) for stainless steel tub models.
Sample compatible models: GDF510PGJ4WW, GDF530PSM4SS, GDF535PGR1WW, GDF630PGM1WW, GDT625PGJ0BB, GDT625PSJ0SS, GDT655SSJ2SS, ADT521PGF6WS, GDF520PGJ2WW, GDT535PSJ0SS
- Genuine OEM GE dishwasher tub gasket — factory original, not aftermarket
- Black flexible plastic — conforms to the door panel under latch compression
- Seats in the channel around the tub opening without adhesive or fasteners
- Creates a watertight seal that prevents leaks during all cycle phases
- Made in the USA
- No tools required — less than 15 minutes to install
| Part Number | WD08X23476 |
| OEM Part Number | WD08X23476 |
| Condition | New |
| Brand | GE |
| Part Type | Dishwasher Tub Gasket |
| Appliance Type | Dishwasher |
| Color | Black |
| Material | Plastic |
| Compatible Brands | GE, Hotpoint, Crosley |
| Supersedes | WD08X10088, WD08X20674, WD08X22094 |
Cancel any running cycle and turn off the dishwasher before beginning. This repair involves only the door gasket channel — no electrical disconnection or plumbing work is needed. Open the door fully and pull the old gasket out of the channel by hand, starting at the top corner. Clean the channel thoroughly — remove any mineral deposits, food debris, or detergent residue that could prevent the new gasket from seating. Press the new WD08X23476 into the channel starting at the top center and working evenly down both sides. Ensure it is fully seated around the entire perimeter with no gaps, kinks, or sections riding above the channel. Close the door to verify the gasket compresses evenly, then run a short rinse cycle and check for leaks at the front of the tub.
Have a question?

WD08X23476 Dishwasher Genuine OEM Tub Gasket

