Skip to product information
Sale
  • Sku: W10909685

W10909685 Dryer Genuine OEM Thermal Fuse

List Price:  $82.00
$53.10
 per 

FREE SHIPPING TO ALL 48 CONTIGUOUS STATES
Free standard shipping at checkout.

CHECK YOUR MODEL COMPATIBILITY

Enter your appliance model number to check if this part is listed as compatible.

Need help finding your model number?

Guaranteed safe checkout

Product description

W10909685 Dryer Thermal Fuse — Genuine OEM Whirlpool Part

The W10909685 is a genuine OEM Whirlpool thermal fuse that serves as the dryer's last line of defense against overheating. When exhaust temperature at the blower housing exceeds 195°F, this non-resettable fuse opens the circuit permanently, cutting power to the heating system or motor depending on the dryer model. Testing is straightforward — a multimeter continuity check across the two terminals will read near zero ohms on a good fuse and open (no continuity) on a blown one.

Before replacing the fuse, it is critical to diagnose why it blew. A thermal fuse does not fail on its own — something drove the exhaust temperature past its rating. The root cause in the vast majority of cases is restricted venting: lint accumulation inside the exhaust duct, a crushed transition hose behind the dryer, or a blocked exterior vent hood. Less commonly, a seized blower wheel, a failed cycling thermostat that stopped regulating heat, or a shorted heating element can push temperatures past the fuse's threshold. Replacing the W10909685 without identifying and correcting the airflow problem guarantees the new fuse will blow again.

QUICK ANSWER

Will This Fix Your Dryer?

If your dryer won't start, runs without heat, or shuts down mid-cycle, the thermal fuse is the first component to test. Set a multimeter to continuity and probe across the fuse terminals — no continuity means the fuse is blown and this genuine OEM W10909685 replacement will restore the circuit. If the fuse tests good (near zero ohms), the problem is elsewhere — the cycling thermostat, heating element, or igniter should be checked next.

Common Symptoms

  • Dryer will not start — no response when cycle is selected
  • Drum turns but heating element or gas burner does not activate
  • Dryer runs for several minutes then shuts off completely
  • Multimeter reads open circuit (no continuity) across fuse terminals
  • Clothes come out damp after a full cycle

Cross Reference Information

The W10909685 is the current Whirlpool part number for this thermal fuse and replaces all previous versions listed below. Any of these numbers found on an existing fuse or in a service manual confirms this is the correct replacement.

W10909685, 4461025, G4AP0506, TF 091C ACA2, W10693363, AP6034383, AWP42948, EAP11766766, FIX11766766, PD00036363, PS11766766
COMPATIBILITY

This thermal fuse is designed for select Whirlpool, Maytag, Kenmore, Amana, Crosley, and Inglis dryers in both gas and electric configurations. Confirm your model number matches before ordering.

Sample compatible models: WED5620HW1, WED8500DC1, WED5100HC0, MGD3500FW0, NED5800HW1, NGD5800HW1, MGD6630HC3, WGD8620HC0, WGD9620HC3, MED6230RHW

Key Features

  • Genuine OEM Whirlpool part — factory-spec thermal fuse
  • 195°F non-resettable cutoff prevents dryer overheating
  • Direct blower housing mount — original connector and screw pattern
  • Works across gas and electric dryer platforms
  • Supersedes previous part number W10693363
  • Two-terminal design for simple multimeter testing and installation

Specifications

Part Number W10909685
OEM Part Number W10909685
Condition New
Brand Whirlpool
Part Type Thermal Fuse
Appliance Type Dryer
Temperature Rating 195°F
Location Blower Housing
Color White
Compatible Brands Whirlpool, Maytag, Kenmore, Amana, Crosley, Inglis
Replaces W10693363
Safety Warning
Never bypass a thermal fuse by jumpering the terminals together. The fuse is a critical fire-prevention device. A blown thermal fuse is a symptom — the root cause is almost always restricted venting. Disconnect the exhaust duct and inspect the full run from the dryer cabinet to the exterior wall cap before installing the new fuse. Operating a dryer with restricted airflow risks lint ignition inside the duct or cabinet.

Frequently Asked Questions

How do I test the thermal fuse with a multimeter?
Unplug the dryer and locate the thermal fuse on the blower housing — it is a small white component with two wire terminals. Disconnect both wires and set your multimeter to the continuity or lowest ohms setting. Touch one probe to each terminal. A good fuse reads near zero ohms (you will hear a continuity beep). A blown fuse reads OL or shows no continuity. If the fuse is open, it must be replaced — there is no way to reset it.
Where exactly is the thermal fuse located?
The W10909685 mounts on the blower housing inside the dryer cabinet. On most Whirlpool and Maytag models, you reach it by removing the lower rear access panel. The fuse is a small white plastic component attached with a single mounting screw, with two flat wire connectors (spade terminals). It sits near the exhaust outlet where heated air exits the drum and enters the blower assembly.
What is the difference between a thermal fuse and a cycling thermostat?
A cycling thermostat opens and closes repeatedly during normal operation to regulate temperature — it is resettable and designed to cycle. A thermal fuse is a one-time safety device that blows permanently when temperature exceeds its rated limit (195°F for the W10909685). The cycling thermostat keeps the dryer in range; the thermal fuse shuts everything down when something goes wrong. Both are located on or near the blower housing but serve very different functions.
What changed between W10693363 and W10909685?
The W10909685 is Whirlpool's current superseding part number for the W10693363. It is a direct functional replacement with the same 195°F rating, mounting points, and connector type. Whirlpool periodically updates part numbers during manufacturing revisions. If your dryer originally came with a W10693363, the W10909685 is the correct current replacement — the older number is no longer produced.
Can I temporarily bypass the thermal fuse to test the dryer?
No — never bypass the thermal fuse under any circumstances. Jumpering the terminals removes the dryer's last line of defense against fire. If you suspect the fuse is the problem, test it with a multimeter to confirm. If it reads open, replace it with a new W10909685. There is no safe shortcut — the fuse exists specifically to prevent the dryer from operating when exhaust temperatures have exceeded safe limits.
Genuine OEM Part Fast Shipping In Stock 30–60 Min Install
View full details
W10909685 Dryer Genuine OEM Thermal Fuse  Parts-O-Matic

W10909685 Dryer Genuine OEM Thermal Fuse

List Price:  $82.00
$53.10
 per 
SUBHEADING

Recently viewed products

Free Shipping

Fast, Free Shipping – No Surprises, Just Savings! Enjoy FREE shipping on all orders within the continental United States. No minimums, no hidden fees—just the parts you need, delivered straight to your door at no extra cost!

Top-notch support

Because Your Time Matters! At Express Parts Direct, we’re committed to providing exceptional customer service. Whether you need help finding the right part, troubleshooting an issue, or tracking your order, our knowledgeable team is here to assist you every step of the way. Experience fast, friendly, and expert support—because you deserve the best!

Satisfied or refunded

100% Satisfaction or Your Money Back! We stand by the quality of our parts and service. If you’re not completely satisfied, we’ll make it right—or refund your purchase. Shop with confidence knowing that your satisfaction is our priority!