- Sku: 5304539804
5304539804 Universal Oven Flat Igniter
FREE SHIPPING TO ALL 48 CONTIGUOUS STATES
Free standard shipping at checkout.
CHECK YOUR MODEL COMPATIBILITY
Enter your appliance model number to check if this part is listed as compatible.
Need help finding your model number?
5304539804 Universal Oven Flat Igniter (Silicon Carbide Hot-Surface Igniter for Gas Ranges) — Genuine OEM
Product Description
The 5304539804 is a genuine OEM flat-style hot-surface igniter for Electrolux-manufactured gas ranges and wall ovens. When a gas oven won't heat, the igniter is the most frequently failed component — but it is not the only possible cause. A systematic diagnosis before ordering saves time and avoids replacing a part that wasn't the problem. The igniter works by drawing current through the oven's gas safety valve. If the igniter draws enough current, the valve opens and gas reaches the burner. If the igniter has weakened, it still glows but cannot pull enough amperage to open the valve. If the igniter has cracked through completely, it won't glow at all and no current flows.
The diagnostic starting point depends on what the igniter does when you turn the oven on. If the igniter does not glow at all, the problem may not be the igniter — it could be a tripped breaker, a failed oven control board, a blown thermal fuse in the oven circuit, or a wiring fault. If the igniter glows brightly and the burner lights normally, the igniter is working and the problem is elsewhere — possibly the oven temperature sensor, the control board, or a door switch. If the igniter glows but the burner never lights (or takes several minutes to light), the igniter is the most probable cause. This last scenario — a glowing igniter that won't open the gas valve — accounts for the majority of "oven won't heat" service calls on these ranges.
Quick Answer
Is Your Oven Igniter the Problem?
If your gas oven's igniter glows for more than 60–90 seconds without the burner lighting, the igniter has likely weakened below the gas safety valve's amperage threshold and needs replacement. If the igniter does not glow at all, check that the range has power (clock and cooktop should work), the oven controls are set correctly, and no breaker has tripped — a non-glowing igniter can indicate an upstream electrical issue rather than a failed igniter. If the igniter glows and the burner lights but the oven doesn't reach temperature, the problem is more likely the oven temperature sensor or control board than the igniter. The 5304539804 is the genuine OEM replacement for select Frigidaire, Kenmore, Electrolux, Tappan, Gibson, and White-Westinghouse gas ranges and wall ovens.
Common Symptoms
- Igniter glows orange/red for several minutes but oven burner never lights
- Gas oven does not heat — igniter does not glow at all
- Oven preheat time has gradually increased over weeks or months
- Oven heats some days but not others (intermittent ignition failure)
- Igniter glows weakly compared to when the oven was new
- Faint gas smell near oven but burner does not ignite
Replaces Part Numbers
The 5304539804 is the current Smart Choice genuine OEM universal flat igniter for Electrolux-family gas ranges. It replaces numerous earlier Frigidaire and Electrolux igniter part numbers as well as industry cross-reference and catalog numbers.
Compatibility & Model Cross Reference
This genuine OEM igniter fits select gas ranges, wall ovens, and microwave/oven combos manufactured by Electrolux and its subsidiary brands. Always confirm your specific model number against the manufacturer's parts diagram before ordering.
Frigidaire: FFGF3054TS, LFGF3054TF, FGGF3036TF, FGF368GCA
Kenmore: 790.70113700, 790.71313700, 790.36903900
Electrolux: EW30GF65GS, EI30GF45QS
Tappan: TGF317ESA, TGF336ASD
Gibson: GGF3032KB
White-Westinghouse: WGF324BHWD
This is a partial list of verified sample models — not every model from these brands uses this igniter. Your model number is typically located on a label inside the oven door frame, on the back panel of the range, or behind the bottom storage drawer. Not sure if this fits? Send us your model number and we'll confirm compatibility before you order.
Key Features
- Genuine OEM Smart Choice flat-style silicon carbide hot-surface igniter
- 3.2–3.6 amp operating range matched to Electrolux/Frigidaire gas safety valves
- Flat ceramic block design — 1-1/2" block, approximately 3.72" overall length
- Includes 2 ceramic wire nuts for secure high-temperature wire connections
- 17-1/2" bare wire leads — no plug connector; wire-nut connection
- Universal fit across Frigidaire, Kenmore, Electrolux, Tappan, Gibson, White-Westinghouse, Crosley, and Kelvinator gas ranges
Product Specifications
| Part Number | 5304539804 |
| Condition | New |
| Brand | Smart Choice |
| Part Type | Flat Style Oven Igniter (Hot-Surface, Silicon Carbide) |
| Appliance Type | Gas Range, Wall Oven, Microwave/Oven Combo |
| Material | Silicon carbide element on ceramic base with metal mounting bracket |
| Igniter Length | Approximately 3.72" (3-3/4") |
| Ceramic Block | 1-1/2" |
| Wire Leads | Approximately 17-1/2" bare leads, 2-wire |
| Amperage Range | 3.2–3.6 amps |
| Includes | Igniter with mounting bracket, 2 ceramic wire nuts, instruction sheet |
Installation & Safety Notes
Disconnect the range from electrical power and turn off the gas supply valve behind the range before beginning any work. The silicon carbide igniter element is extremely fragile — do not touch it with bare hands, as skin oils create hot spots that cause premature cracking. Handle the igniter by its ceramic base and wire leads only. After installation, restore gas and power, turn the oven on, and visually confirm that the burner lights within 90 seconds. Check all connections for gas leaks. If you smell gas at any point, shut off the gas supply, ventilate the area immediately, and do not operate any electrical switches.
Frequently Asked Questions
- How can I tell if the problem is the igniter or the gas safety valve?
- In most cases, it's the igniter. The gas safety valve and the igniter are wired in series — the same current flows through both. The valve opens only when the igniter draws enough amperage. A weak igniter that glows but can't pull enough current is by far the more common failure. The gas safety valve itself rarely fails. If you replace the igniter and the oven still won't heat — the new igniter glows bright white but the valve still doesn't open — then the valve is the next component to suspect. Do not replace the gas safety valve first; the igniter is the correct starting point in the overwhelming majority of "oven won't heat, igniter glows" scenarios.
- What does it mean when the igniter glows but the oven doesn't heat?
- It means the igniter is drawing some current — enough to glow — but not enough to reach the gas safety valve's opening threshold. A healthy igniter draws between 3.2 and 3.6 amps at operating temperature. As the silicon carbide element degrades, its resistance increases and the amperage drops. The igniter may still glow orange or even bright orange, but if the current is below the valve's minimum (typically around 3.2 amps), the valve stays shut and no gas reaches the burner. This is the classic symptom of a failing igniter and is the single most common gas oven repair.
- How do I test an oven igniter before ordering a replacement?
- There are two approaches. The observational test is the most practical for homeowners: turn the oven on and watch the igniter through the oven window or with the door slightly open. If it glows bright white and the burner lights within 60 seconds, the igniter is good. If it glows orange or dim red for more than 90 seconds without the burner lighting, it has weakened and needs replacement. If it doesn't glow at all, disconnect power and check for continuity across the igniter with a multimeter — an open-circuit reading (OL/infinity) confirms the element has cracked through. For the precise amperage test, a technician can use a clamp-style ammeter on the igniter circuit wire to measure live current draw — refer to your model's service manual for the manufacturer-specified amperage threshold.
- What else besides the igniter can cause a gas oven not to heat?
- Several components can produce similar symptoms. If the igniter does not glow at all, check for a tripped circuit breaker, a blown oven thermal fuse (separate from the igniter), a failed oven control board, or a wiring harness fault — any of these can prevent power from reaching the igniter circuit. If the igniter glows and the burner lights but the oven doesn't reach temperature, the oven temperature sensor (thermistor) or the control board is more likely at fault. If you smell gas but the oven won't light, the gas supply may be partially blocked or the safety valve could be stuck — this requires professional diagnosis. A range with working cooktop burners but a non-working oven has confirmed gas supply to the appliance, so the problem is in the oven-specific circuit: igniter, safety valve, control board, or wiring.
- Why does my oven sometimes preheat normally and sometimes take forever?
- Intermittent ignition is a hallmark of an igniter that is right at the borderline of the gas safety valve's amperage threshold. The igniter's resistance changes slightly with ambient temperature, humidity, and the residual heat in the oven cavity from recent use. On some attempts, it draws just enough current to open the valve; on others, it falls a fraction of an amp short. This intermittent stage can last days or weeks before the igniter degrades further and fails consistently. If your oven has entered this pattern, the igniter is reliably failing and replacement is the correct repair — waiting longer only extends the period of unreliable cooking.
Have a question?

5304539804 Universal Oven Flat Igniter

