Skip to product information
Sale
  • Sku: 5215ER2002G

5215ER2002G Washer Genuine OEM Drain Hose Assembly

List Price:  $49.50
$38.95
 per 

FREE SHIPPING TO ALL 48 CONTIGUOUS STATES
Free standard shipping at checkout.

CHECK YOUR MODEL COMPATIBILITY

Enter your appliance model number to check if this part is listed as compatible.

Need help finding your model number?

Guaranteed safe checkout

Product description

5215ER2002G Washer Drain Hose Assembly — Genuine OEM

When an LG front-load washer leaks, the drain hose is one of several possible sources — and pinpointing where the water is coming from determines whether this is the right part. Water on the floor behind an LG washer during or just after the drain cycle points to the drain path: the drain pump, the pump-to-hose connection, the hose body, or the hose-to-standpipe end. Water that appears during fill or wash cycles usually means the door boot seal, water inlet valve, or tub-to-pump hose instead. Timing is the first diagnostic — drain-cycle-only leaks narrow the field to the drain side, and the 5215ER2002G covers the longest stretch of that path.

The OE error code on LG washers means the control board did not detect adequate water removal within its programmed window. That code can come from a clogged pump filter, a failed pump motor, a kinked or blocked drain hose, or a plugged standpipe. Before replacing the hose, clear the pump filter first — it is accessible behind the small service panel at the front bottom of most LG front-loaders. If the filter is clean and the pump motor runs (you can hear it hum), the restriction is downstream: either the hose is kinked, internally clogged with lint and detergent residue, or cracked enough that it leaks out instead of pushing water up to the standpipe.

QUICK ANSWER
Will This Fix Your Washer?

If your LG front-load washer leaks behind the machine only during the drain cycle, throws an OE error code with a clean pump filter and a running pump motor, or the existing drain hose is visibly cracked, kinked, or swollen, the 5215ER2002G is the genuine OEM replacement. If the leak occurs during fill or wash — not during drain — check the door boot seal, inlet valve hoses, and tub-to-pump hose instead.

Common Symptoms
  • Water leaking behind the washer only during the drain or spin cycle
  • OE error code with a clean pump filter and an audible pump motor
  • Drain hose is visibly cracked, split, or kinked behind the machine
  • Water backs up into the tub instead of draining completely
  • Hose pops out of the standpipe under pump pressure
Cross Reference Information

The 5215ER2002G is LG's current part number for this drain hose assembly. The letter suffix has been revised multiple times as LG updated the hose design. All earlier revisions and distributor catalog numbers are listed below.

5215ER2002G replaces AEM73773301, 5215ER2002Q, 1268108, 4932ER3008A, 5215ER2002B, 5215ER2002C, 5215ER2002D, 5215ER2002E, 5215ER2002F, 5215ER2002N, 5215ER2002R, 5215ER2002S, 5215ER2002Y, AEM75033801, AGM75511501, ALG51596, AH3527325, AP4457291, EA3527325, PD00005676, PS3527325

COMPATIBILITY

This genuine OEM drain hose assembly fits select LG and Kenmore front-load washers and washer-dryer combos. The hose has molded ends sized for LG drain pump outlets — confirm your model number before ordering to ensure correct fit.

Sample compatible models: WM2077CW, WM2277HW, WM2650HRA, WM3570HWA, WM3670HVA, WM3001HRA, WM2101HW, WM2487HWMA, WM3375HWA, CW2079CWD

Key Features
  • Genuine OEM LG drain hose assembly — factory original, not aftermarket
  • Approximately 2 meters (6.5 feet) of flexible corrugated hose
  • Gray corrugated rubber/plastic construction for kink-resistant routing
  • Molded pump-end and discharge-end fittings match LG factory connections
  • Supports standpipe installations up to 96 inches high
  • Fits LG and Kenmore front-load washers and washer-dryer combos
Specifications
Part Number 5215ER2002G
Condition New
Brand LG
Part Type Drain Hose Assembly
Appliance Type Front Load Washer / Washer Dryer Combo
Hose Length Approximately 2 meters (~6.5 feet)
Material Flexible Corrugated Rubber/Plastic
Color Gray
Max Standpipe Height 96 inches
Compatible Brands LG, Kenmore
Supersedes 5215ER2002F, 5215ER2002C, 5215ER2002B
Safety Warning
Unplug the washer and shut off both hot and cold water supply valves before disconnecting the drain hose. Residual water will drain from the hose when disconnected — place towels and a shallow pan under the pump connection to catch it. If the washer is on a pedestal, have a second person steady the machine when you pull it forward to access the rear connections. Do not kink or sharply bend the new hose during routing — a kinked section restricts flow and creates the same draining problems the replacement was meant to fix. Secure the discharge end in the standpipe with the hose form bracket to prevent it from ejecting under pump pressure.
Frequently Asked Questions
How do I tell if the leak is from the drain hose and not the drain pump?
Run a drain cycle and watch the connections with a flashlight. The drain pump sits low on the front of the machine, and its hose connections face the rear. If water seeps from the clamp where the hose meets the pump housing, the clamp is loose or the pump outlet gasket is worn — that is a pump-side issue, not a hose issue. If the pump connections are dry but water appears along the hose body or at the standpipe end, the hose itself is the source. A crack in the corrugated section will drip only while the pump is running and pressurizing the hose, so the leak may stop between drain cycles.
The washer throws an OE code but I see no visible leak. What should I check first?
Start with the drain pump filter — it is behind the small access panel on the front bottom of most LG front-loaders. Coins, hair ties, button fragments, and lint accumulate there and restrict flow. If the filter is clean, check the hose for internal blockage by disconnecting both ends and running water through it. A hose that is clogged with detergent sludge or lint will pass water slowly or not at all. Also check the standpipe itself by pouring a gallon of water directly into the pipe — if it backs up, the household drain line is blocked downstream and the washer hose is not the problem.
Could a kinked drain hose cause the OE code without any visible leak?
Yes. A kink restricts the internal diameter of the hose and reduces water flow without breaking the hose wall. The pump motor runs but cannot push water through the restriction fast enough, and the control board times out and throws the OE code. Kinks typically form where the hose makes a tight turn behind the washer or where it was pinched when the machine was pushed back against the wall. Pull the washer forward and inspect the entire hose run from pump to standpipe. If the hose holds the kinked shape even after straightening, the rubber has taken a permanent set and the hose should be replaced.
What is the difference between the drain hose and the tub-to-pump hose?
The tub-to-pump hose is a short internal hose that connects the bottom of the wash tub to the inlet side of the drain pump — it carries water from the tub down to the pump by gravity. The drain hose (5215ER2002G) connects the outlet side of the pump to the standpipe or household drain — it carries water away from the pump under pressure. They are two separate hoses on opposite sides of the same pump. A leak from the tub-to-pump hose usually shows water under the front of the machine during wash and drain cycles. A leak from the drain hose shows water behind or beside the machine during the drain cycle only.
My old hose is marked 5215ER2002B (or C, D, E, F). Is the 5215ER2002G the same hose?
Yes. The letter suffix indicates a revision — LG updates the suffix when they change a material, supplier, or molding detail. The 5215ER2002G is the current revision and directly replaces all earlier versions (B, C, D, E, F, N, Q, R, S, Y). The hose length, end fittings, and pump connection are the same. If your parts diagram or old hose shows any of those numbers, the 5215ER2002G is the correct current replacement.
Genuine OEM Part Fast Shipping In Stock ~30 Minute Install
View full details
5215ER2002G Washer Genuine OEM Drain Hose Assembly  Parts-O-Matic

5215ER2002G Washer Genuine OEM Drain Hose Assembly

List Price:  $49.50
$38.95
 per 
SUBHEADING

Recently viewed products

Free Shipping

Fast, Free Shipping – No Surprises, Just Savings! Enjoy FREE shipping on all orders within the continental United States. No minimums, no hidden fees—just the parts you need, delivered straight to your door at no extra cost!

Top-notch support

Because Your Time Matters! At Express Parts Direct, we’re committed to providing exceptional customer service. Whether you need help finding the right part, troubleshooting an issue, or tracking your order, our knowledgeable team is here to assist you every step of the way. Experience fast, friendly, and expert support—because you deserve the best!

Satisfied or refunded

100% Satisfaction or Your Money Back! We stand by the quality of our parts and service. If you’re not completely satisfied, we’ll make it right—or refund your purchase. Shop with confidence knowing that your satisfaction is our priority!