- Sku: 3363394
3363394 Washer Drain Pump Replaces WP3363394
FREE SHIPPING TO ALL 48 CONTIGUOUS STATES
Free standard shipping at checkout.
CHECK YOUR MODEL COMPATIBILITY
Enter your appliance model number to check if this part is listed as compatible.
Need help finding your model number?
3363394 Washer Direct Drive Drain Pump — XPARTCO Aftermarket
Product Description
The XP-3363394 is an XPARTCO aftermarket replacement for the Whirlpool WP3363394 drain pump used in beltless direct-drive top-load washers. These pumps fail in predictable ways, and understanding what kills them helps prevent repeat failures. The most common cause of pump failure is foreign objects — coins, buttons, bra underwires, hairpins, and small clothing items that slip through the gaps around the tub drain and lodge in the pump's impeller chamber. When a hard object jams between the impeller and the volute housing, the motor stalls during drain, producing a loud humming noise. Sometimes the object passes through and the pump resumes draining, but the impeller blades may already be chipped or scored, reducing pump efficiency.
The second most common failure is a housing crack at the seam where the two halves of the pump body join. Years of thermal cycling — hot wash water followed by cold rinse water, cycle after cycle — fatigues the plastic at the junction. The crack starts as a hairline that weeps a few drops per load, often going unnoticed until water stains appear on the floor under the washer. Left unaddressed, the crack widens until the pump leaks steadily during every drain cycle. That leaked water runs down the motor shaft and corrodes it, which creates a secondary problem during installation: the new pump's shaft seal cannot seat properly on a rusted motor shaft, and the new pump leaks from day one unless the shaft is cleaned first.
Quick Answer
Is Your Washer Drain Pump the Problem?
If your Whirlpool direct-drive top-load washer won't drain, leaks from underneath, or hums loudly during the drain cycle, the pump is a likely cause. Before ordering, check the drain hose for blockages and verify the lid switch is working — both cause identical no-drain symptoms without any pump fault. If the pump housing is cracked at the seam or the impeller won't turn freely by hand, the pump needs replacement. The XP-3363394 is a direct-fit aftermarket replacement for the OEM WP3363394 and all earlier versions of this pump.
Common Symptoms
- Washer won't drain — standing water remains in the tub after the cycle
- Water leaks from underneath the washer during drain or spin cycles
- Loud humming noise during drain — motor running but water not moving
- Grinding or rattling sound from the pump area during drain
- Slow drain — tub takes much longer than normal to empty
Replaces Part Numbers
The XP-3363394 is an XPARTCO aftermarket replacement for the Whirlpool OEM drain pump and all of its earlier part numbers, catalog numbers, and cross-references.
Compatibility & Model Cross Reference
This aftermarket drain pump fits select Whirlpool-manufactured direct-drive top-load washers and washer-dryer combos. It is a direct-fit replacement for the OEM WP3363394 across the same model range. Always confirm your specific model number against the manufacturer's parts diagram before ordering.
Whirlpool: LSQ8243HQ0, LSQ8543JQ0, WTW5540SQ0, LSR7233EQ0, LSR8233EQ0, LXR9245EQ0
Kenmore: 11081350100, 11024812200, 11024952300, 11020936993
KitchenAid: Select direct-drive top-load washer models
Maytag: Select direct-drive top-load washer models
Roper: Select direct-drive top-load washer models
Estate: Select direct-drive top-load washer models
Admiral / Amana / Crosley / Inglis / Norge: Select direct-drive top-load washer models
This is a partial list of verified sample models — not every model from these brands uses this pump. This pump fits beltless direct-drive washers only. Your model number is typically on a sticker inside the lid or on the rear cabinet panel. Not sure if this fits? Send us your model number and we'll confirm compatibility before you order.
Key Features
- XPARTCO aftermarket replacement — direct-fit equivalent of OEM Whirlpool WP3363394
- Two-port design: 1-3/4" large tub intake port and 1-1/4" smaller drain outlet port
- Mounts directly to the washer motor shaft with two spring clips
- No belt required — designed for the Whirlpool beltless direct-drive platform
- No electrical connections — pump is driven mechanically by the motor shaft
- Two-piece off-white plastic housing with internal impeller
Product Specifications
| Part Number | 3363394 |
| OEM Part Number | WP3363394 |
| Condition | Aftermarket |
| Brand | XPARTCO |
| Part Type | Direct Drive Drain Pump |
| Appliance Type | Top Load Washer, Washer Dryer Combo |
| Material | Plastic |
| Color | Off-White |
| Intake Port | 1-3/4" diameter (tub connection) |
| Outlet Port | 1-1/4" diameter (drain hose connection) |
| Mounting | Two spring clips to motor shaft |
Installation & Safety Notes
Unplug the washer before working on the drain pump. Tip the washer back and support it securely. Have towels and a shallow pan positioned underneath — water will drain from the hoses when you disconnect them. Before installing the new pump, check the drain hoses for foreign objects. Coins, buttons, and fabric fragments that jammed the old pump may still be lodged in the hoses and will immediately jam the replacement. Inspect the motor shaft for rust or pitting — clean it with fine emery cloth and apply silicone grease if needed. Install the new pump, secure the spring clips, reconnect both hoses, and verify all clamp connections before lowering the washer.
Frequently Asked Questions
- What foreign objects commonly jam the drain pump?
- Coins are the most common culprit — they slip past the tub drain opening and wedge between the impeller blades. Buttons, bra underwires, hairpins, paper clips, and small clothing items (baby socks, washcloths) are also frequent causes. Some of these objects pass through the pump and end up blocking the drain hose instead. Before every pump replacement, disconnect the drain hose and check it for debris. When you remove the old pump, check inside the volute chamber for trapped objects before discarding it — knowing what jammed the pump helps prevent a repeat failure.
- Can too much detergent damage the drain pump?
- Excess detergent does not damage the pump directly, but it creates secondary problems that stress the pump. Oversudsing produces thick foam that the pump cannot move efficiently — the impeller cavitates instead of pumping water. Over time, detergent residue and undissolved powder accumulate in the pump chamber and drain hose, narrowing the passages and forcing the pump to work harder. This buildup also traps lint and small debris that would otherwise wash through, increasing the chance of an impeller jam. High-efficiency (HE) detergent used in correct amounts reduces this risk significantly.
- How do I clear a jammed pump impeller without replacing the pump?
- If the impeller is jammed by a foreign object but the housing is not cracked, you may be able to save the pump. Unplug the washer, tip it back, and remove the pump from the motor shaft. Disconnect the hoses and look into the intake port — you can often see the obstruction. Use needle-nose pliers to extract the object through the port opening. Once removed, spin the impeller by hand to verify it moves freely and check for chipped or cracked impeller blades. If the blades are damaged, the pump will still function but with reduced efficiency, and pieces of broken blade can re-jam the impeller later. In that case, replacement is the more reliable repair.
- Why does the pump leak at the housing seam and not at the hose connections?
- The two halves of the pump housing are joined at a molded seam around the circumference of the pump body. This seam is a structural joint, not a gasket-sealed connection — it relies on the precision of the plastic molding and the mechanical bond between the two halves. Over years of thermal cycling (hot wash water followed by cold rinse water), the plastic at the seam fatigues and develops hairline cracks. The hose connections, by contrast, are secured with adjustable clamps that maintain compression against the port nubs. A seam crack is not repairable — once the housing cracks, the pump must be replaced.
- How often do direct-drive washer drain pumps need replacement?
- There is no fixed service interval. Many direct-drive washer pumps last the life of the machine (15–20 years) without failure. The two things that shorten pump life are foreign objects reaching the impeller and long-running leaks that go unaddressed. Checking pockets before loading the washer, using a mesh laundry bag for small items, and promptly investigating any water under the machine are the most effective ways to extend pump life. If you are replacing the pump for the second time and the washer is otherwise in good condition, consider installing an inline lint trap on the drain hose to catch debris before it reaches the pump.
Have a question?

3363394 Washer Drain Pump Replaces WP3363394

